- 1 Where should toilet supply line be placed?
- 2 How high is a toilet valve?
- 3 What is code for toilet space?
- 4 What is standard toilet dimensions?
- 5 Which fill valve for toilet is best?
- 6 Why is my toilet water level too high?
- 7 Why does the water in the toilet bowl get low?
- 8 How much clearance do you need between toilet and vanity?
- 9 How much space do you need between toilet and sink?
- 10 Is a 24 inch door too small for a bathroom?
- 11 What is the highest toilet height?
- 12 What is the difference between standard height and comfort height toilets?
- 13 How do I know if my toilet is a 10 or 12 rough?
Where should toilet supply line be placed?
Water Supply Line Install a ½ inch copper water line to the location of your new toilet. Insert the line through the bottom plate on the wall, approximately 8 inches to the left of the toilet’s center line.
How high is a toilet valve?
It actually depends on the toilet model, some (one piece) toilets require the water supply stub out to be lower than the ever so common 6″ from floor, 6″ from center.
What is code for toilet space?
Most codes require at least 15 inches (measured from the center of the toilet) from any side wall or obstruction and not closer than 30 inches center to center to any other sanitary fixture. (The NKBA actually recommends 32 inches.) There should be at least 24 inches of clear space in front of a toilet or bidet.
What is standard toilet dimensions?
Standard toilet dimensions are typically between 28–30″ deep, roughly 20″ wide, between 27–32″ high, and have a rough-in between 10–14″.
Which fill valve for toilet is best?
The 5 Best Toilet Fill Valves
- Fluidmaster 400AH PerforMAX.
- Toto TSU99A. X Universal Fill Valve.
- Kohler Genuine Part Gp1083167.
- Fluidmaster 400CRP14 Universal Toilet Fill Valve.
- Korky 528 Universal Fill Valve.
Why is my toilet water level too high?
Adjust the Fill Height by Checking the Float The water level in the tank is controlled by an adjustable float. A float that’s set too low produces a weak flush; if it’s set too high, water spills into the toilet overflow tube and the fill valve won’t shut off.
Why does the water in the toilet bowl get low?
The most common reason your water level is low is because your fill tube is damaged or broken in some way. This small, flexible plastic hose is the main control of your water level. Or, the toilet bowl may be cracked, causing water to leak onto the bathroom floor.
How much clearance do you need between toilet and vanity?
NKBA designers recommend a 30″ clearance between the front edge of a fixture, such as a vanity or toilet, and any other fixture or wall. The building code allows for a minimum of 21″.
How much space do you need between toilet and sink?
Plan a clear floor space of at least 30 inches from the front edge of all fixtures (lavatory, toilet, bidet, tub, and shower) to any opposite bath fixture, wall, or obstacle. Code Requirements: A minimum space of 21 inches must be planned in front of the lavatory, toilet, bidet, and tub.
Is a 24 inch door too small for a bathroom?
If you’re working with a really small space you could bring the door width down to 28 inches or 71cm, even down to 24 inches or 61cm as an absolute minimum (note – small doors are should only be used for bathrooms, closets and utility rooms). A full bathroom usually requires a minimum of 36 to 40 square feet.
What is the highest toilet height?
Today’s so-called “comfort height” or “right height” toilets feature bowls that are 17 to 19 inches high, as compared to the standard 15 inches of a regular toilet. The higher bowl height can be good for the knees and back and can offer real advantages to taller folks, the elderly and people with mobility problems.
What is the difference between standard height and comfort height toilets?
The difference between standard height and comfort height toilets is approximately two inches. It will measure 17 to 19 inches from the floor to the seat. Often this height toilet is priced less than the standard height toilet. There are a few drawbacks to this raised toilet.
How do I know if my toilet is a 10 or 12 rough?
To determine the size of your toilet rough-in, measure from the wall behind the toilet to the bolt caps of your current toilet. Most toilets are available in a 12-inch rough-in, which is the standard distance, but a 10- or 14-inch rough-in may be needed in some homes.