- 1 What size is the water inlet on a toilet?
- 2 How tight should toilet water supply line be?
- 3 What side is the water supply on a toilet?
- 4 Should a toilet cistern be screwed to the wall?
- 5 How a cistern system works?
- 6 How do you access a concealed toilet cistern?
- 7 Can you connect a garden hose to a toilet?
- 8 Why is my toilet supply line leaking?
- 9 Are toilet water supply lines Universal?
- 10 Can a toilet drain into a 2 inch pipe?
- 11 Can a toilet supply line be too long?
- 12 What size is my water shut off valve?
What size is the water inlet on a toilet?
The supply line to the toilet is standard 1/2-inch copper or plastic pipe routed from the main water line or a 1/2-inch cold water line. This standard is used throughout the home to supply faucets, showers and any other appliance requiring water, including the washing machine.
How tight should toilet water supply line be?
Normally you should be okay hand tightening it and then giving it an eight to a quarter turn with a good pair of channel locks. Tighten it until it stops leaking, an 1/8th turn at a time.
What side is the water supply on a toilet?
Originally Answered: Can you install the water supply on the right side of the toilet tough in? Yes, but toilets in the US are made to have the inlet on the left. If you put the supply on the right you will need a long and unsightly supply line from the stop valve to the toilet inlet.
Should a toilet cistern be screwed to the wall?
That’s where this toilet gets its name. Low Level Toilet Cistern – A traditional style cistern for traditional toilets; low level cisterns are fixed just above the pan and usually have a gap between them and the pan. Most cisterns have a way of being fixed to the wall so check your cistern and grab a tape measure.
How a cistern system works?
Roof-catchment cisterns are systems used to collect and store rainwater for household and other uses. A system of gutters and downspouts directs the rainwater collected by the roof to the storage cistern. The cistern supplies water to the household through a standard pressurized plumbing system.
How do you access a concealed toilet cistern?
How to Get Into a Concealed Toilet Cistern in 10 Steps
- Locate the toilet cistern’s push button.
- Slightly lift the cover plate and remove it.
- Carefully remove the flushing rods located at the centre of the concealed cistern frame.
- Unfasten any plastic bolts manually to release the frame.
Can you connect a garden hose to a toilet?
No, no, no. Ballcocks (toilet fill valves) have always had their own thread type. No pipe is ever designed to screw on to the ballcock threads directly. All connections must be some sort of compression, i.e. rigid or flexible toilet supply line or pex adapter fitting.
Why is my toilet supply line leaking?
A leak can also be because of worn out washers and/or threads. Turn off the water at the shut off valve and remove the hose. Remember, there will be water in the hose so have something like a small Tupperware or bucket to catch it.
Are toilet water supply lines Universal?
Built to last this universal design fits all common toilets and valves. Size adapters are included with this supply line that fits 3/8 in. Replacing old, or leaking toilet connectors is easy with Fluidmaster’s universal toilet supply lines.
Can a toilet drain into a 2 inch pipe?
Unless two toilets are on the same drain and then it must be a 4-inch plumbing waste pipe, the toilet requires a drain pipe of 3 inches in diameter. Unless there is a toilet discharging into the piping, systems with less than nine units can use a 2-inch pipe.
Can a toilet supply line be too long?
Ignore the Length The length of the flex line is immaterial. When the shutoff valve on the water pipe is opened to allow water into the line, the water builds up pressure in the flex line regardless of the length. The hot water may be delayed for one or two seconds, but the water pressure will be unaffected.
What size is my water shut off valve?
Shut-off valves come with different-sized outlet ports. The two most common are 3/8- and 1/2-inch compression or male pipe thread. Faucets connectors aren’t completely standardized, but most have 1/2-inch male pipe thread connectors.